- Extends pedals - Not for use on exercise bikes

Converts 3-bolt LOOK style shoes to SPD MTB compatible cleats

- The ATAC 13/17° cleat works with all TIME mountain pedals. - Included with all mountain pedal models numbered "6" and higher - Release angles of 13 degrees or 17 degrees depending on how the cleat is set up on the shoe - Compatible with all two-hole cycling shoes.

PIN KIT FOR OUR COMPOSITE PEDALS KIT CONTAINS: - 40 THREADED M3x10mm SOCKET HEAD PINS - 40 NYLOCK NUTS

Everything you need to fully rebuild your OneUp Aluminum Pedals. Our V2 kit is compatible with all OneUp Aluminum pedals. The brass bushings take the place of the 3 small cartridge bearings and aluminum washer that were on our original pedal assembly. KIT CONTAINS - 2 LARGE OUTER BEARINGS - 2 BRASS BUSHINGS - 2 OUTER SEALS - 2 FLANGE WASHERS - LH AND RH AXLE BOLTS - 2 AXLE O-RINGS - LH AND RH BEARING NUTS

HEIGHT ADJUSTMENT WASHERS AND PINS FOR OUR ALUMINUM PEDALS KIT CONTAINS - 40 - HEXIGONAL TIPPED M4 THREADED SOCKET HEAD PINS - 40 - 0.8mm THICK HEIGHT ADJUSTMENT WASHERS

Traditionally, mountain cleats have only had two material options. Mild steel and brass. This has largely been to ensure that the cleat wore out faster than the pedal interface, but has left us with cleats that are often times very fast wearing, and in all cases, are quite heavy. Enter 6/4 Titanium, only slightly less hard than tool or spring steel used in the pedals, it's a remarkable 2.25 times stronger and 3 times tougher than brass or mild steel. Best of all, the extreme toughness and abrasion resistance of 6Al/4V titanium means that you can expect 300-400% wear life compared to traditional materials. Now we couldn't just stop there, but by combining 3D printing technology with this material that is 1/3 lighter than steel, we are able to achieve a cleat with internal lattice structure (called a gyroid) which maintains stiffness and strength while reducing weight to create a cleat set that is HALF the weight of a standard cleat set. This savings of 25-30 grams per set of cleats is significant over time, particularly in CX events where running is crucial. 25gm reduction x 100 rpm = 180kg of mass not lifted per hour of riding, 90kg per leg!

Longer rear load pins for the outer extremities of your pedals provide ultimate durability, while shorter front load center pins create a virtual concavity in the pin pattern, increasing grip without sacrificing pedal body thinness. - 28pcs rear load pins - 16pcs front load pins - Tool included

- Compatible with all Spike & Oozy Pedals - Full Complement Sealed Bearing x 2pcs - Green Silicone Friction Seals - Replacement inboard bearings for your SPIKE or OOZY pedals.

X-TRACK cleats are compatible with all SPD-standard pedals, utilizing 2-screw mounting for an ultra compact profile and lightweight. X-TRACK Easy cleats provide a 13° angle of disengagement and allow for multidirectional release. - Compatibility: X-Track and Geo Trekking Collection, SPD compatible - Material: Premium Steel - Clip out direction: Multidirectional - Clip in: 30% easier - Angle of Disengagement: 13° - Lateral Adjustment: 2mm - Angular Adjustment: 1° - Weight (pair): 45g

- Chrome plated steel clips for double toe strap - Hardware included - Deep size for shoes with a larger toe-box

Official replacement cleats for Ritchey mountain bike pedals. - Includes a pair of cleats and mounting hardware - Compatible with Ritchey Pro-V4 and V5 mountain clipless pedals

Origin-8's Double Steel Toe Clips feature the classic toe clip look and style, with double strap compatibility. And, they are built to the same standards held for Japanese Keirin racing.

- Works with all XPRO and XPRESSO pedals. - Not included with new XPRO and XPRESSO pedals. - This is a zero-float cleat design, so there are zero (0) degrees of heel float and no lateral float along the pedal axle. - Compatible with all three-hole road shoes, but the included shim may be required for shoes that have a large curvature in the forefoot area. Full details are included in the easy-to-use instructions.

Crank Brothers' 5050 Pin Kit includes 40 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.

Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.

- Allows a customer to replace their cleats. - Two replacement cleats in box

A revolution in performance and reliability. The kit includes premium internal components: - Enduro catridge bearings - Enduro sealed needle bearing - Double seal system (internal and external seals) - Hex alloy end caps - O-rings, nuts - Sleeve bushings - Bearing removal tool

The Blade Kit for the Keo Blade Carbon range is compatible with ceramic and Ti models. It allows you to replace the original blade or change the tension of your pedals to fit your requirements. 3 different tensions are available: 12 for standard use, 16 for sprinters and a recommended 20 for track cycling.

The Activ Grip Trail Pads are compatible with our Trail Grip platform pedals. Built from extremely strong and durable material and designed in collaboration with outdoor specialist Vibram, they offer exceptional traction on the toughest rides. Their concave geometry is enhanced with large rubber lugs and composite studs for optimal foot stability and extreme durability to take on the challenges of any terrain.

Replacement pin set for Race Face Atlas and Aeffect pedals.

- Fits most MTB shoes - For clipless SPD-style pedals - 4-degree float

The DELTA standard requires a rotational movement of the foot toward the outside or inside for disengagement. This function improves cyclist's safety; no body or bearing prevents disengagement toward the inside. Compatible with non-KEO LOOK pedals, their contact area is wide for optimal comfort. They also feature a memory positioner to aid when changing cleats. - Use: Road & Indoor Bike - Material: Polyacetal + PTFE - Lateral adjustment: 4mm - Longitudinal adjustment: 12mm - Weight (pair + fasteners): 75g

- Fixie style straps that are compatible with most flat pedals - Provide the pulling power of straps with the easy release of clipless pedal system - Stiff, wide straps do not need toe clips

The XPro & Xpresso cleats have been developed for the TIME XPro & Xpresso road bike pedal range. They allow angular and lateral freedom in order to respect the natural movements of your legs and joints. You can also adjust the Q-factor (by switching the cleats) in order to optimize performance, following 3 points: security, ergonomics, and performance. The Bi-material brings more durability when walking with the cleats. These cleats are the stock cleats included with all XPro & Xpresso pedals.

- Look ARC Delta compatible - 9° rotation allows natural foot movement - Includes mounting hardware

- Shimano SPD-SL-style - Engineered thermoplastic injection body - Weight of 24 grams per cleat - 4.5-degree floating arc

The Keo Spacer adaptors are slim wedges that fit between the shoe and the cleat. They aim to avoid the unpleasant creaking sound provoked by contact between the sole and the cleat, which can arise in particular with flat-soled shoes. Delivered with 2 spacers and 6 screws for quick and easy installation.

- Chrome plated steel strapless toe clip - Hardware included

The Cleat Screw Kit is a bike fitter's best friend because it eliminates the difficulty (and in some cases impossibility) of finding the perfect type and length of cleat screw. - The Kit contains 150 screws (15 different screw types/sizes with a quantity of 10 each) - SPD / MTB Compatible Cleat Screws - 4mm Hex countersunk M5x0.8, compatible with most 2-hole cleats, and are black oxide coated carbon steel. Kit includes 10 of each: 10mm (PD0219), 12mm (PD1576), 14mm (PD1577), and 16mm (PD1578). - Look / Shimano Compatible Cleat Screws - 4mm Hex Button Head M5x0.8, are compatible with most 3-hole cleats, and made from stainless steel with Nylock®. Kit includes 10 of each: 8mm (PD1579), 10mm (PD1580), 12mm (PD1581), 14mm (PD1582), 16mm (PD1583), 18mm (PD1584), and 20mm (PD1585). - Speedplay Walkable Compatible Cleat Screws - Phillips Recessed Button Head - M4x0.7, are 4-hole cleat compatible and made from stainless steel with Nylock®. Kit includes 10 of each: 9mm (PD1590), 11mm (PD1591), 13mm (PD1592), and 15mm (PD1593).